LATTICE FENCING VINYL HOW TO
LATTICE FENCING VINYL PORTABLE
LATTICE FENCING VINYL PROFESSIONAL

Position the saw exactly along the pencil line, then begin cutting the lattice with care and precision.

Squeeze the saw’s trigger and cut along the line slowly and steadily.

The extra length of the teeth is too large, causing the plastic to chip.

A reciprocating saw or a Sawzall with fine teeth can also be used, but anything with a high-speed saw blade suited for wood should be avoided.

Use a vinyl-cutting blade for plastic or solid core vinyl lattice.

Plastic lattice is typically 0.5 in thick, but you can double-check the thickness with a ruler.

To secure, push the blade lever back into place.

Hold the saw against the lattice as if you were about to cut it, then lower the blade to about 0.5 inches below the lattice’s level.

Release the blade lever on the back of a circular saw to adjust the blade depth.

To keep the lattice stable and help you cut in a straight line, place many clamps at either end of the lattice away from the cut line.

Next, place the lattice on the surface with the front, or imitation wood grain side, facing down. A strong plank or a worktable will suffice.

To cut the lattice, lay it face down on a flat surface.

This will make the cutting procedure easier and reduce the chances of staples flying up and harming you.

Manufacturers commonly use Staples and nails to help the lattice keep its shape, although they can be dangerous when sawing.

Remove any staples or nails along the pencil line using a flat screwdriver.

Carefully draw a light line down the back of the lattice where it has to be trimmed with a carpenter’s pencil.

Mark the lines where it has to be cut once you’ve got your measurements.

Draw a straight-cut line on the lattice with a straightedge and a pencil.

Work gloves should be used while handling and cutting the lattice, just in case any splinters or chips fly. To safeguard your eyes, wear plastic safety glasses.

LATTICE FENCING VINYL PORTABLE

Circular saws work like table saws yet are portable and cut wood on site.Įven with a fine-toothed blade to prevent chipping, you must take caution when using circular saws in the garden.īefore you saw it, put on safety equipment. Here you can see the proper ways you should cut lattice panels. ( Read Best Way To Cut Vinyl Siding) Is It Easy To Cut Vinyl Lattice? To avoid chipping, wear eye protection and possibly a mask to stop breathing dust while cutting vinyl. Carefully guide the saw blade through the lattice. Note: If you don’t have a vinyl-cutting blade, use a fine-toothed blade. Cut the post evenly, and then replace the cap. Measure your length and cut straight with your fine-toothed saw. Remove the post’s cap if you need to cut a post already in the ground. Doing this means you can hide any cuts in the soil.

When cutting posts, start at the bottom and cut your way up. You can rip fence posts with your trim saw to finish the job. Re-notch your fence rails by sliding vinyl fence notchers into the end of your cut rail.

LATTICE FENCING VINYL PROFESSIONAL

This will result in clean cuts and a professional finish. Saw between, not through, fence panels or pickets. Use a circular saw with your vinyl-cutting blade to now cut your vinyl fence. You can now cut your vinyl fence components. Then, use a circular saw and a vinyl-cutting blade to cut through the lattice, joint by joint. Next, draw a line down the length of your vinyl with a T-Square guide and note where you need to cut. With a pencil, mark this distance on your vinyl. Measure the distance your fence material needs to cover with a tape measure.

Make sure your cuts are straight and smooth to prevent chipping and give your vinyl project the most outstanding possible appearance. Whether you’re building a fence yourself or working on another vinyl fence job, you’ll almost certainly need to trim your material to match your needs. Vinyl fence and PVC lattice can be cut in the same ways as wood: a table or circular saw. ( Read Can You Stain Particle Board) What Do I Use To Cut vinyl lattice?

LATTICE FENCING VINYL HOW TO

To make things far more straightforward, we have a guide on how to cut lattice the right way.īy the end, you’ll have all you need to find the right tools to make a task that you can accomplish quickly, with only a little bit of effort. Vinyl lattice may be cut to size in the same ways that wood lattice can however, certain saw blades and the sort of saw you can use are better for the work than others. Vinyl is almost maintenance-free, and when it requires attention, it’s usually only a quick wash to remove dirt and dust, which you can do easily with a power washer. However, handling and cutting it might be difficult. Plastic lattice is an excellent landscaping item since it won’t rot, is insect-resistant, and is simple to maintain. Vinyl is increasingly gaining popularity as a substitute for making a fence, rails, or even replacing a wooden lattice or wood fencing.

Lattice fencing vinyl